Support Rods For J Hooks, Data Cable Hangers & More

j hook shooter rodWhen ceiling grid wire hangers or pencil rod doesn’t  offer enough rigidity or code won’t allow you to use a ceiling grid wire to support your hangers, consider our SC14 shooter rod hangers.  The SC14 shooter rods are designed for use in Ramset, Hilti, Powers, Simpson and other powder actuated tools.   Available with in lengths from 12″ to 36″ these hangers lend themselves to many install applications.  Use them with an Arlington Loop or j hooks for fast cable hanger installs.  One very common install involves mounting  a j hook or loop at the bottom and then adding a second j hook or loop with a mutli clip midway up the rod.  These can be assembled on the floor and installed with a powder tool on an extension pole.

Many electricians are using them for their BX cable runs.  Simple shoot in and fasten your BX cable with a clip like the Caddy KX clip.  Simple to use, open the box and shoot!  The uses for these shooter clips are endless.  

Overhead Fastening With The Ramset Viper 4

Ramset has been making quality powder actuated tools for years.  The Viper tool quickly became a favorite tool of anyone doing overhead fastening.  Whether hanging ceiling wires, light fixtures or data cable runs, the Viper tool is designed specifically for shooting to the ceiling.  The earliest version was a very simple tool that required manual advance.  The tool was a real work horse but it required daily cleaning.  The latest version, the Ramset Viper 4 is a great tool for overhead fastening.   The tool offers automatic advance and a unique pole system that is stable and expandable from 3′ to the moon just by adding extension segments.  The Viper 4 tool has the added safety feature of a separate sleeve for activation making it safer than other contact tools.  You can’t just lean on the tool by mistake and set it off, it must be in contact with the ceiling, and both hands on the pole.  I would add an important point on the Ramset Viper 4 tool:  POLES ARE NOT INTERCHANGEABLE WITH PREVIOUS MODELS!  We are finding that many online marketers not only don’t understand the tools, but don’t understand the importance of the right extension for the tool.  If you have any questions on the Ramset Viper 4,  visit our store online at ConstructionFastening.Net or call us toll free at 1-877-212-2377.

 

 

 

 

Turn Your Lagmaster Plus Eye Lag Pole Into A Heavy Duty Extension Pole

Lagmaster plus extension pole broom thread plugYou can turn your Lamgaster Plus eye lag pole into a heavy duty extension poles simply by adding the Lagmaster Plus Broom Thread Plug. Now your Lagmaster plus is a a heavy duty extension pole that will accept any attachment with broom thread including brushes, light bulb changers, tree saw ends, paint rollers, sanding pads, the list goes on and on. Accepts any broom thread.  You can find the Lagmaster Plus pole tool, the Lagmaster Plus Broom Thread Plug and a complete line of specialty tools and fasteners on line at ConstructionFastening.Net

Crane Gopher Pole Push Pull Pole

Crane 90520 Gopher Pole Push Pull PoleWhile there are many brands of gopher poles or push pull poles on the market,  time and again, the preference seems to be the Crane 95020 Gopher Pole.  The Crane 90520 gopher p0le or push pull pole is telescopic, 52″ while collapsed and extends to 22 feet and weighs under 4 lbs.  Some of  bigger electrical supply houses have moved away from the Crane Gopher pole for  lines such as Greenlee and others, but still ask the contractors and they will tell you they prefer the Crane 90520.   One real plus the telescopic design offers is when you are on the ladder, you have the complete tool with you and you can feed it out rather than fumbling with sections screwing them on then adding another length and so on.  If you have never tried a  Gopher 90520 push pull gopher pole, give it a try and see why it has been preferred gopher pole for years.

Better Success Fastening Ceiling Clips With Your Ramset & Hilti Powder Tools

Hilti and Ramset tools have been a great asset to many trades including the data comm field for hanging cable hooks. Overhead fastenings can be a challenge in some concrete. Power Point Ceiling Clip For Hilti Ramset ToolsIf your having trouble with low success rates when shooting ceiling clips into the concrete deck above, the problem many times can be traced back to the quality of your pin. Most tool supply houses and even the big box stores offer pins and loads for Ramset and Hilti tool. The problem is, many are stocking the cheapest pins available to maximize sales and profit. The result is that when you run into brittle concrete or pre cast decks, you can have a lot of blow outs. If you are shooting up a ceiling clip with pre attached, every failed fastening can start to add up. If you are having more blow outs than you like, or you are getting a lot of fish hooked pins, consider a ballistic point pin like the Ramset SPC78 and Ramset SPC114 series of ceiling clips. These clips are assembled using a polished point pin rather than a standard “pinched” point. See the pictures, there is a difference. Add to that the thicker shank on these ceiling clips and you will see fewer blow outs and less fish hooking of your pins. The SPC114 pin has an even thicker shank than the SPC78 and while you may not be able to sink it all the way, get it in 3/4″ and you will have a solid support for your light fixtures and cable hooks. For even better success, use a Ramset or Hilti tool made just for overhead work like the Ramset Viper 4.

 

https://plus.google.com/u/0/104549669036941549854

When To Replace Your Ramset Cobra Piston SC301200A

ramset cobra piston SC301200AThe Ramset Cobra tool has become a staple for many of the trades including the low voltage and electrical trades.  The Ramset Cobra is what we call a Hilti DX-350 clone tool as is the Simpson PT27 and tools from other manufactures as well.  This is a well proven design that is easy to use and quite reliable.  One of the things I like is how stable it is when mounted on a ceiling extension pole tool, making it a great choice for ceiling grid wires for suspending not only ceilings but j hooks and light fixtures.  One of the most common wear parts on these tools is the piston, or drive pin.  How can you tell when it is time to replace the piston on your Ramset Cobra?  Murphy’s law dictates that what can go wrong will so even if you piston looks good, having a spare will save you down time.   When your piston is new, it has taper around the end.  Like a tent stake that expands when repeatedly pounded, the piston will start to flare over time.  This bevel accommodates this flare.  If you piston is starting to flare or chip, it is time to replace it, or at the least have one on hand.  As for the ring, typically they will last the life of the piston.  You can replace them but it isn’t easy.  To replace the piston on your Ramset Cobra, slide the annular spring to release the piston stop and slide out the barrel.  Remove the barrel clip and now the barrel halves will come apart.  Simply pull out the old piston and replace it.  Reassemble the tool in reverse order.  If you have any problems or questions, give a call toll free at 1-877-212-2377 and we will walk you through.    Find a complete line of Ramset Cobra parts here.

The Ramset XT540 Power Adjustable Powder Tool

If you are running into applications where you are needing more power or would like a durable .27 caliber strip tool for shooting concrete and steel, Ramset XT540consider the Ramset XT540 tool.  The XT540 offers an automatic return and power adjustment feature.  You can actually drop two power levels with the power adjustment wheel.  Designed to develop the power needed to handle a full 3″ pin.  If you job calls out a .157 check out the Ramset .157 shank true embedment pins, stamped with the size of the pin.  A magazine and lathing disc attachment are available as well.  So if you need a little more power, consider the Ramset XT540 tool, made in USA.

Coring With SDS Hammer Drill Core Bits

sds core bitIf you do any amount of cabling in commercial buildings, you can’t avoid pulling cables through masonry applications. Typically you will need to drill anywhere from a 1″ to 4″ hole to accept a sleeve of some kind be it a piece of EMT conduit or a pass through device. You have several choices. Number one, you can hire someone to core the holes for you. If there is another trade already coring through the wall, cost may not be so bad. If you have to hire a coring contractor, it can get expensive. There are times when hiring someone is the best way to go. If you have a lot of holes, bigger holes or you have post stressed concrete, you may be better off passing the liability and cost to a concrete cutting coring firm. Choice number two involves poking a bunch of smaller holes with a hammer drill and then breaking out the center. There are times where this may get you buy, but consider an easier option first. SDS core bits. Most contractors today utilize SDS hammer drills. These hammers can also perform coring jobs quite well. A standard SDS hammer like a Hilti TE15 or Bosch 11255 hammer should be able to 2-1/2″ core with relative ease. The core bits used for these types of hammers are carbide tipped and have a thin wall. This thin creates less resistance than what you may find on bigger core bits making for an easy drill.

Check out the video, you will be impressed on the speed!  Click here to find Bosch Speed Core SDS Thin Wall core system.

 

 

Safety First With Ramset & Hilti Tools

Safety first.  We here it all the time but what does it mean to be safe when operating a Hilti, Ramset or other powder actuated tool?  There is the ramset cobraobvious and please don’t skip thesm basics as some do.  Safety glasses.  A Hilti, Ramset or any powder actuated tool develops enough power to sink a nail into 1/2″ steel.   That should be enough power to put a piece of that pin or other fragment through your eye lid!  Secondly, use your hearing protection.  When using a Hilti or Ramset tool on an extension pole like when you are installing pre tied grid wires for ceilings or supporting fixtures and data cable runs, the tool may be far enough away from the operator for your comfort, but it is still recommended.  If you fasten into steel with a powder actuated tool, you will likely only make the mistake of not wearing hearing protection once, it will leave your ears ringing.  Certification is required on powder actuated tools.  You can get certified on a Ramset tool on Ramset’s website.  Besides the obvious safety guidelines, certification will give you more safety guidelines for proper application and nail selection when using your Ramset or Hilti tool.

Keeping your powder actuated tool clean and in proper repair is often overlooked.  If any of your tool parts are chipped or cracked, replacing them now can not only save you down time later but could vary well prevent an injury.  You can find a complete line of Ramset Parts.  If you need any assistance with your powder actuated tools, you can give us a call toll free at 1-877-212-2377.

Extra Long SDS Hammer Drill Bits For Hilti, Bosch, Dewalt and Others

If you are faced with the challenge of drilling an extra deep or long hole in masonry, you know it can be a real challenge to find a hammer drill bit long enough for your SDS hammer drill.  Usually you can find a bit that will drill up to about a foot, but some projects, especially projects that are older buildings or additions will require you to drill deeper holes. Now what?  Be prepared.  We offer a full line of SDS bits from 3/8″ to 3/4″ diameters that will give you a drill depth of anywhere from 16″ to 34“!   If you need a whole a little wider, you can drill a pilot with the smaller diameter and then come from either side if possible.  We have bits 7/8″ diameter to 1-1/4″ that have 16″ diameters.  If you have an application that requires a larger hole, consider one of our thin wall cores designed for use with SDS hammers.  You will find a size range of 1-9/16″ to over 4”.  There thin wall design reduces the amount of friction allowing even small to medium size SDS hammers to handle up to  2-1/2″ hole or more with ease.

Click here for extra length SDS bits.

extra long sds hammer drill bit

Is my hammer an SDS hammer?  Sometimes we get the question, especially with Hilti hammers, is my hammer an SDS hammer drill?  If it is a smaller hammer, likely so.  It can get confusing, with some brands.  For instance, Hilti calls the bits for SDS hammers a TE-CX bit.  An SDS shank hammer drill bit is about 3/8″ diamter and has to dimples opposite each other, and two slots opposite each other.  If that is what you have, any SDS bit will fit in to your hammer drill.  If the shank is about 3/4″ you likely have an SDS Max or possibly a spline bit.  These are typically bigger, and noticeably heavier tools.

bosch thinwall speedcore

 

Click here for the Bosch Speedcore System